Welcome to
Caldwell Carpet's
Online Carpet Website

We Accept Credit Cards




Roppe Rop Cord Commercial Entry Tiles

Buy Roppe Rop Cord Commercial Entry Tiles

Roppe Entry Commercial Tiles

Roppe Rop Cord Commercial Entry Tile is a super heavy duty flooring option. These Commercial Entry Tiles are very slip resistant and can be used in indoor and outdoor environments. These Entry Tiles are made using recycle truck tires that are bonded together in rows. Roppe Rop Cord Entry Tiles are for areas like retail stores and airports.

Made for the most demanding applications, Rop-Cord is durable, anti-slip flooring with outstanding sound absorption properties. May be used as a walk-off mat for entryways, lobbies, concourses, and foyers in shopping malls, grocery stores, airports, factories, office buildings, skating rinks, schools, theaters, bowling alleys, ski lodges, and other demanding indoor an d outdoor applications. Available in a durable non-vulcanized and vulcanized version.

Non-Vulcanized Rop-Cord is constructed of strips from a biased ply truck tire that are bonded to a spunbond polyester backing and then buffed to reveal the cord of the tire. It is the cord that provide the appearance of the Rop-Cord. These cords are left natural in the earthtone and then dyed to create the colored appearances.

Vulcanized Rop-Cord is constructed in the same manner with one exception, the strips are bonded to a rubber backing through a vulcanization process.

All dimensions and packaging are for both the non-vulcanized and vulcanized versions of the product.

Call 800-772-7090 With Your Commercial Entry Tile Questions.

Rop Cord 110NPO
Specifications

Gauge: 3/8" (9.52 mm)
Size: 12" x 12" (304.8 mm x 304.8mm)
Packaging: 25 Pcs (25 Square Feet / Carton)

Eligible For Leed Credit
Made With 90% Post-Consumer Waste

Earth Tone - $9.95 / Piece
Colors - $13.50 / Piece

Rop Cord Tile Compared To A Quarter
Roppe Rop Cord Commercial Entry Tile - 110NPOCR Crimson
CR Crimson
$13.50 / piece
Roppe Rop Cord Commercial Entry Tile - 110NPOET Earth Tone
ET Earth Tone
$9.95 / piece
Roppe Rop Cord Commercial Entry Tile - 110NPOIN Indigo
IN Indigo
$13.50 / piece
Roppe Rop Cord Commercial Entry Tile - 110NPOPN Pine
PN Pine
$13.50 / piece

TECHNICAL DATA

Product Classification

  • ASTM does not currently offer requirements for this product category

Recycled Content

  • 90% Post-Consumer

Fire Testing Information

  • ASTM D 2859 (FF 1-70, 16 CFR 1630), Ignition Characteristics - Passes

BENEFITS & LIMITATIONS

  • Can be used outdoors
  • Meets ADA recommendations for use on ramps.
  • We do not recommend the application of Dyes to re-color product after fading.
  • Cannot be installed over substrates containing Radiant Heat.
  • Do not leave edges exposed, side edges can roll and delaminate, finish with appropriate trims.
  • Not to be used in Commercial Kitchens or other areas subjected to animal, vegetable or petroleum based oils and solvents.
  • Not to be used in areas subjected to sharp spikes, cleats, sharp wheels, stiletto heels or other objects that could damage the flooring.
  • Not to be used in direct contact with heat sources.
  • Staining may occur if allowed to remain in contact with strong staining agents such as tires, walk-off mats, disinfectants, cleaning agents, pesticides or other chemicals (solid, liquid or gas).
  • Long term, extended or excessive exposure to UV Heat " Light will cause discoloration or other undesirable affects, colored tiles will fade back to Earthtone color.
  • Use appropriate floor protection devices for resilient flooring on all furniture or fixtures. Dragging or improperly moving furniture or equipment across the surface of the tile can cause permanent damage

NON-VULCANIZED ROP-CORD RUBBER FLOOR TILE

Rop-Cord Non-Vulcanized tile shall be homogenously constructed of select reclaimed commercial tile components, reinforced with a polyester non-woven fabric bonded to a thin-adhesive layer. Tiles shall be 3/8" nominal thickness, shall conform to industry standards and shall contain no asbestos fiber. Floor covering shall be 12" x 12" (304.8mm x 308.4mm) tiles, and in the color _________ selected (insert color name and number selected).


INSTALLATION

Product is designed for installation in a parquet or quarter-turned fashion. Installation in a linear fashion can cause undesirable effects not covered by the product warranty.

  • Read all literature concerning the product description, product limitations, substrate preparation, adhesive information, adhesive application, product installation procedures and warranty before installation.
  • Deliver all materials to the installation location in its original packaging with labels intact and remove any plastic stretch wrap and do not stack materials.
  • Inspect all material for proper type and color prior to installation.
  • Store products in a dry area protected from the weather on a smooth, flat, dry surface with temperatures maintained between 65º F (19º C) and 85º F (30º C).
  • Inspect all substrates prior to installation.
  • All substrates must be clean, smooth, permanently dry, flat, and structurally sound.
  • The substrate must be free of moisture, dust, sealers, paint, curing compounds, parting agents, residual adhesives, adhesive removers, hardeners, resinous compounds, solvents, wax, oil, grease, asphalt, gypsum compounds, alkaline salts, excessive carbonation or laitance, mold, mildew, any other extraneous coatings, films, materials and all other foreign matter which might interfere/restrict proper adhesive bonding.
  • In renovation or remodel work, remove all existing adhesive residue so that 100% of the overall area of the original subfloor/substrate is exposed.

Acclimation for Indoor Installations

Maintain product, adhesive & substrate between 65ºF (19ºC) and 85ºF (30ºC) for at least 48 hours before installation, during installation, and after installation to ensure proper product and adhesive functionality . Ensure temperature of the substrate is within this range as well prior to installation. Proce ed with the installation only when the co nditions are proper and correct and all other trades have completed their work.

Acclimation for Outdoor Installations

Maintain product & adhesive indoors between 65ºF (19ºC) and 85ºF (30ºC) for at least 48 hours before installation and during installation as much as possible. Temperature fluctuation outdoors will affect adhesive and product stability and functionality. Ensure the ambient and substrate temperature is between 65ºF (19ºC) and 85ºF (30ºC) if possible. Roppe is not responsible for installation and product issued outside of this range when installing outdoors. Ways to control this includes, but is not limited too, temporary coverings to cool the areas, installing during periods of day within this range, not installing outdoors during winter, etc. Proceed with the installation only when the conditions are proper and correct and all other trades have completed their work.

Tile Installation

  • Square the area and determine reference points for installation
  • Apply adhesive according to the label directions and allow proper open time
  • Whenever possible avoid any seams directly on seams in the substrate and borders less than half of the width of the material
  • Do not install over expansion joints
  • When laying the flooring, use a kneeling board, or for best results work off of the flooring whenever possible to prevent adhesive displacement
  • If the adhesive is bleeding or oozing at the seams, there is too much adhesive or the adhesive is too “wet”, allow the adhesive to flash longer before placing additional tiles
  • Immediately remove excessive wet adhesive with a soft, clean cloth dampened with warm soapy water
  • Periodically, lift the tiles to check for proper adhesive transfer. There should be adequate adhesive transfer to the back of the tile
  • Observe the adhesive to assure that the adhesive has not surpassed the open time and beginning to cure
  • Cut borders and other specialty cut tiles to fit snugly, not tightly, against the wall, threshold, transition strip, fixtures, or other obstacles; forcing incorrectly sized tiles into smaller areas will cause buckling of the tile
  • Leave approximately 1/8" gap around perimeter of room in case of expansion, ensure gap is no larger than the trim or wall base being applied
  • Roll and cross roll each section of tile laid with a 100-pound 3 section roller within 15 minutes after installation of the tile section. Adjust rolling times if necessary according to climate conditions. Use a hand roller in areas that cannot be reached with the larger roller. Conduct a visual inspection during the rolling process to assure there has been no shifting of the tiles and that there is no adhesive on the surface of the tile
  • Do not wait until completing the entire installation before rolling as the adhesive may have surpassed the open time and cured. Roll and cross roll a second time approximately 30 minutes after the initial rolling

After Installation Protection of Flooring

  • When moving in appliances or heavy furniture, it is always wise to protect the flooring and accessories from scuffing and tears by using something to protect the floor such as Masonite, Ram Board or heavy construction paper
  • Use floor protectors under furniture or fixtures to reduce indentation; as a rule of thumb, the heavier the item the wider the floor protection device needed
  • Place walk-off mats at outside entrances manufactured with non-staining backs to prevent discoloration

MAINTENANCE

  • Sweep and/or Vacuum with high CFM vacuum*
  • Spot clean and/or shampoo as needed
  • Exterior installations can be hosed and left to dry
  • Initial cleaning 72 Hours after installation

Approved Cleaners

Spartan Chemicals Green Solutions All Purpose Cleaner, Spartan Chemicals Clean by Peroxy, Johnson Stride, Taski Profi and/or a Mild Soap & Water Solution for Shampooing

Roppe Rop-Cord Recycled Rubber Tile is a low maintenance product that does not require waxes or finishes. Lack of regular or routine maintenance will diminish the look and appearance of the flooring.

Initial Maintenance

  • Allow 72 hours after in stallation for proper curing of the adhesives
  • Remove any coverings used to for floor protection after installation prior to cleaning
  • Sweep and/or vacuum floor with a high CFM vacuum to remove any dirt or particulates accumulated on the floor
  • Spot clean and /or shampoo to remove any stains

Daily Maintenance

  • Sweep and/or vacuum floor with a high CFM vacuum to remove any dirt or particulates accumulated on the floor
  • Spot clean and/or shampoo to remove any stains

Weekly Maintenance

Keep in mind, if the appearance of the flooring becomes unacceptable; this procedure may require completion more frequently to provide acceptable appearances.

  • Sweep and/or vacuum floor with a high CFM vacuum to remove any dirt or particulates accumulated on the floor
  • Spot clean and/or shampoo to remove any stains
  • Use an extractor when necessary to remove any dirt or particulates accumulated on the floor or between strips
  • Exterior applications can be hosed and left to dry, if pressure washer is used be careful not to loosen the bond with the adhesive

The use of a highly alkaline, highly acidic or solvent-base cleaners or products will remove color from the flooring or degrade the flooring prematurely. DO NOT use sweeping or cleaning agents containing oil or solvents. DO NOT allow the solution to work its way beneath the flooring which could result in an adhesive failure. Caution: When wet, flooring will become slippery; therefore, use the appropriate warning signs on the floor to eliminate foot or other traffic.

Floor Finishes

There are no known finishes that can be applied to this product. We do not recommend the application of dies to attempt to color or re-color this product.

Floor Protection Devices

  • When moving in appliances or heavy furniture, it is always wise to protect the flooring and accessories from scuffing and tears by using something to protect the floor such as Masonite, Ram Board or heavy construction paper
  • Use floor protectors under furniture or fixtures to reduce indentation; as a rule of thumb, the heavier the item the wider the floor protection device needed
  • Place walk-off mats at outside entrances manufactured with non-staining backs to prevent discoloration

WARRANTY INFORMATION

Limited 1 (one) Year Manufacturers’ Warranty including conformity to written specifications and free from manufacturing defects, subject to the terms and conditions of this document.

Limited 5 (five) Year Commercial Wear Warranty - Lifetime Delamination Warranty
If determined by Roppe to be defective and/or a wear warranty issue, Roppe will replace or repair the material subject to the warranty, however labor costs will be the end user’s responsibility except as provided on the following prorated basis:

  • Year 1, Material & 100% Reasonable Labor
  • Year 2, Material & 50% Reasonable Labor
  • Years 3-5, Material Only
  • Years 5+ for Delamination, Affected Material Only